三维电极处理腈纶聚合废水的条件优化研究

采用填充粒状活性炭的三维电极处理腈纶聚合废水,考察实验条件对污染物去除效果的影响以及废水处理前后可生化性的变化.阳极为Ti/SnO₂-Sb₂O₃网状极板,阴极为网状钛电极,分别考察了停留时间、 电解电压、 pH值、 曝气量对废水中污染物去除效果的影响.结果表明,电解电压和pH值对废水有机物的去除率影响较大,在最优实验条件：电解电压为15V,pH值为3,曝气量400 mL/min的条件下电解120 min,腈纶聚合废水的COD、 TOC和丙烯腈的去除率分别为32.59%、 22.17%和89.70%,并且经过电解处理,废水BOD₅/COD值从0.02上升至0.42,可生化性显著提高,为生物处理提供了条件.     

长海海域浮筏养殖虾夷扇贝生物沉积速率的现场研究

为评价浅海高密度、规模化浮筏养殖贝类的生物沉积作用及其环境生态效应,本文运用生物沉积物捕集器对长海海域浮筏养殖虾夷扇贝的生物沉积速率进行了四个季度的现场测定。结果表明,同一养殖区不同排筏虾夷扇贝的生物沉积速率有很大不同,呈现出由低排筏到高排筏逐渐降低的趋势;不同季节虾夷扇贝生物沉积速率变化明显,秋季最高,冬季最低。海水中悬浮颗粒物浓度及水温是影响扇贝生物沉积速率的主要因素。     

包埋类脂的吸附剂制备及吸附POPs性能

用丙酮作溶剂将三油酸甘油酯分散到醋酸纤维(CA)基体中,采用悬浮聚合的方法制备出了一种兼具亲水性,又能高倍富集持久性有机污染物的球形复合吸附剂。通过对分散剂的种类及其用量、悬浮介质的种类及其用量的研究,获得了球形复合吸附剂的最佳合成路线与工艺.球形吸附剂粒径为1～2mm。通过荧光分析和电镜扫描分析,表明三油酸甘油酯已被包埋到醋酸纤维基体中,并得到了均匀分散。采用七氯、狄氏剂、异狄氏剂、灭蚁灵为代表性的持久性有机污染物(POPs)。动力学吸附实验表明,当初始浓度为1μg/L时,在快速吸附阶段,溶液中80%的氯、狄氏剂、异狄氏剂可得到有效去除,但并没有达到吸附平衡。快速吸附完后,还在持续地进行慢速吸附。而对于灭蚁灵,吸附速度远远低于其他几种POPs。实验证明了吸附速度不仅与辛醇/水系数有关,而且还与有机污染物的分子结构有关。     

Dyes adsorption using a synthetic carboxymethyl cellulose-acrylic acid adsorbent

Removal of noxious dyes is gaining public and technological attention. Herein grafting polymerization was employed to produce a novel adsorbent using acrylic acid and carboxymethyl cellulose for dye removal. Scanning electron microscopy and Fourier-transform infrared spectroscopy verified the adsorbent formed under optimized reaction conditions. The removal ratio of adsorbent to Methyl Orange, Disperse Blue 2BLN and malachite green chloride reached to 84.2%, 79.6% and 99.9%, respectively. The greater agreement between the calculated and experimental results suggested that pseudo second-order kinetic model better represents the kinetic adsorption data. Equilibrium adsorptions of dyes were better explained by the Temkin isotherm. The results implied that this new cellulose-based absorbent had the universaiity for removal of dyes through the chemical adsorption mechanism.     

金属氧化物降解六氯苯的活性比较及催化机理研究

以氧化铝(α-Al_2O_3、γ-Al_2O_3)、氧化钙(CaO)、过渡金属氧化物(Mn O_2、α-Fe_2O_3、γ-Fe_2O_3、Ni_2O_3、CuO)为催化剂,考察了催化剂种类、添加比例等因素对六氯苯(Hexachlorobenzene,HCB)降解效果和产物组分的影响.结果表明,催化效果随催化剂添加比例的提高显著增加.在反应温度为350℃,反应时间1 h,金属氧化物添加比例为100∶1的条件下,碱土金属氧化物CaO及过渡金属氧化物中的α-Fe_2O_3和Ni_2O_3降解活性较好,这3种氧化物对HCB的降解率分别达到65.5%、100.0%和100.0%,脱氯率D_1分别为54.4%、81.9%和77.5%.HCB降解有机产物分析结果显示,8种金属氧化物与HCB样品反应产物中均存在低氯代苯,在α-Fe_2O_3和Ni_2O_3的催化作用下有2~4氯代低氯苯检出,说明在降解过程中存在明显的逐级脱氯/加氢反应;与CaO反应后的产物中低氯代苯较少,经拉曼光谱定性分析,有无序碳的检出,说明除了脱氯/加氢还存在脱氯缩合反应.     

GO-TiO2改性中空纤维膜的制备条件及抗污染性能研究

以氧化石墨烯(GO)与纳米二氧化钛(TiO_2)为改性剂,采用界面聚合法与抽滤吸附结合,对聚偏氟乙烯中空纤维超滤膜(简称原膜)进行表面改性,得到新型纳米改性膜(简称GO-TiO_2改性膜).研究改性膜的制备工艺条件及其对腐殖酸(HA)的吸附截留性能与抗污染特性.结果表明:(1)最佳制备工艺条件为:钛酸丁酯2 m L、GO 1 mg、间苯二胺1%(质量分数)、间苯二胺浸泡时间8 min、均苯三甲酰氯0.2%(质量分数)、均苯三甲酰氯浸泡时间10 min;(2)亲水性提高显著,亲水性表面为GO-聚酰胺-TiO_2复合结构,改性膜接触角由80.6°±1.8°下降到38.6°±1.2°;(3)抗污染性能提高明显.改性膜通量总衰减率由改性前的51.2%下降到35.6%,过滤周期约为原膜的2.5倍;反冲洗后膜通量恢复率由69%提高到96%.     

非离子型聚丙烯酰胺絮凝剂的制备及其絮凝性能

以丙烯酰胺（AM）和烷基酚聚醚（APAP）为单体，采用反相乳液聚合法制备了流动性好的非离子型聚丙烯酰胺絮凝剂（PAM-APAP）。考察了乳化剂和引发剂的种类、单体总质量分数、单体配比和反应温度等因素对聚合反应的影响。实验结果表明，制备PAM-APAP的最佳工艺条件为：单体总质量分数35%、m（AM）∶m（APAP）=9.0∶1.0、Span80+Tween80复配乳化剂加入量为油水总质量的7%、m（Span80）∶m（Tween80）=7.0∶1.5、V50加入量为单体总质量的1.5‰、反应温度50℃。PAM-APAP具有较好的絮凝效果，与其他絮凝剂相比用量较少，在加入量为100mg/L时，对聚合物驱油中产生的含聚合物污水的浊度去除率为87.9%，去油率为89.5%，且絮体不黏壁。     

Leaching,mobility and persistence of tebufenozide in columns packed with forest litter and soil

Abstract

Leaching, downward mobility and persistence of tebufenozide was investigated under laboratory conditions in columns packed with forest litter and soil, after fortification with the analytical grade material (purity > 99.6%) and with two commercial formulations, RH‐5992 2F (aqueous flowable) and RH‐5992 ES (emulsion suspension). Two types of litter and soil were used: one type with relatively high amounts of sand and the other with high amounts of clay.

The concentrations eluted in the leachates were lower when the analytical material (dissolved in acetone) was used for fortification, than when the two formulations (diluted with water) were used. The amount leached was higher for RH‐5992 2F than for RH‐5992 ES. The type of substrate, i.e., sandy or clay type, had only marginal influence on the amounts eluted in the leachates. Downward movement of tebufenozide from the top 2‐cm layer to the untreated middle and bottom layers (3‐cm segments) was consistently lower when the analytical material was used for fortification, than when the two formulations were used. Downward movement was higher for RH‐5992 2F than for RH‐5992 ES. Persistence of tebufenozide in substrates, maintained under submerged conditions for 70 days after leaching, indicated an initial 2‐week lag period prior to the onset of degradation. Formulation‐related differences were observed in the half‐life (DT₅₀) values. When the analytical material was used for fortification, the DT₅₀ ranged from ca 54 to 59 d. However, when the formulations were used for fortification, the DT₅₀ showed a higher range, i.e., from ca 62 to 67 d for RH‐5992 2F and ca 70 to 80 d for RH‐5992 ES. Formulation ingredients appear to have caused enhanced adsorption of tebufenozide onto the substrates, thus delaying degradation.     

膜的改性及其在环境领域应用研究进展

膜改性由于具有清洁、廉价、节能等特点，近年来得到快速发展，是解决膜污染的有效方法之一。本文综合介绍了膜的基体改性、表面改性这两种改性类型和目前常用的改性方法包括表面涂覆、表面活性剂改性、化学修饰改性、仿生改性等等，并简单介绍了膜改性在环境领域的应用，探讨了膜改性今后的发展。     

化工生产事故预防信息系统研究

为指导操作人员正确地处理化工生产过程中的问题,防范人为误操作导致的事故发生,开发了以化工生产的危险与可操作性分析结果和典型事故原因分析结果为知识库的事故预防信息系统.系统实时在线监测化工生产过程中的关键变量,通过判定变量间的影响关系,实现对化工生产过程潜在危险的辨识、预警并给予实时操作指导,以确保生产安全,提高装置的生产效率.最后,以丙烯聚合工艺为例,在多功能过程试验控制平台上进行了验证,探讨了事故预防信息系统的应用方法.